background image

2

RECORD MODEL AND SERIAL NUMBERS BEFORE INSTALLATION! 

Please take a moment to locate the model number and serial number from your fan (see below) and record this information on 

the Warranty page inside the front cover of your Owner’s Manual if it does not appear there already. These numbers are found on 

the motor identification plate affixed to the fan motor in the location shown below:

PLEASE INSPECT ALL PACKAGING PRIOR TO DISCARDING!

Your Casablanca fan was crafted with pride and care and inspected thoroughly prior to shipment. Before 

you begin to assemble and install your Casablanca fan, remove all parts from the carton and check them 

against the Parts Guide in this manual.

Make sure all parts are included in the box using 

the Parts Guide on the following pages. 

If there are missing or broken parts: 
Call  1-888-227-2178  Monday  through  Friday,  8  a.m.  to 

4:30 p.m. CST. Your request will be handled immediately. 

Replacement parts will be sent to you via Federal Express.

Proper Parts Handling

Do not remove lightbulbs from their packaging until you are 

ready to install them. 

Before discarding packaging materials, be certain that all parts 

have been removed. 

Use a clean, dry paintbrush to remove small Styrofoam pieces 

that may remain after unpacking.

Do not brush Styrofoam into wiring cavities. 
The blades in each pack are matched for equal weight to assure 

smooth fan operation. If more than one fan is being installed, 

do not mix blades from different cartons. 

When cleaning, painting, or working near your fan, be cautious 

of the fan and blades.

Always turn power to the ceiling fan OFF before replacing 

lightbulbs or working on your fan. 

Never insert anything into the path of the fan blades while 

the fan is in operation. 

Never install a fan over a pool or spa. 
Never operate a fan that has been damaged in any way. 

Install  the  fan  according  to  the  instructions  in 

this manual.

If the fan does not work:
Refer to the Troubleshooting Tips in this Owner’s Manual.
Call Technical Support at 1-888-227-2178.
Contact your local Authorized Service Center.
Our Web site at www.casablancafanco.com contains additional 

information on Casablanca products, troubleshooting, and 

Authorized Dealer or Service Centers. Please do not return 

this product to the store.

Serial Number

Model Number

Heritage

® 

II

 

TYPE 

  HANGER TYPE

DJ01 1151      MODEL #

C19xxxK

Memphis, TN

 SERIAL No.: 

DJ06 2237

       

C19xxxK

Motor Identification Plate

Summary of Contents for C19xxxK





















Reviews: