background image

These instructions cover the installation of CFSD-XXX 
leakage rated combination fire smoke dampers with 
factory installed actuators and sleeves in corridor ceiling 
applications. These instructions meet the requirements 
of UL 555 and UL 555S.
There are three different configurations available for 
this application. Configurations 1 and 2 apply when 
the fire rated ceiling is also the finished ceiling and the 
damper is installed behind a grille, register, or diffuser. 
Configuration 3 applies when the fire rated ceiling is 
above the finished ceiling and the grille, register or 
diffuser is somewhere below the corridor damper.

Receiving and Handling

Upon receiving dampers, check for both obvious 
and hidden damage. If damage is found, record all 
necessary information on the bill of lading and file 
a claim with the final carrier. Check to be sure that 
all parts of the shipment, including accessories, are 
accounted for.
Dampers must be kept dry and clean. Indoor storage 
and protection from dirt, dust, and the weather is 
highly recommended. Do not store at temperatures in 
excess of 100°F (38°C).

SAFETY WARNING

Improper installation, adjustment, alteration, service 
or maintenance can cause property damage, injury 
or death. Read the installation, operating, and 
maintenance instructions thoroughly before installing 
or servicing this equipment.

Table of Contents

General Information . . . . . . . . . . . . . . . . . . 2
Installation Supplements.   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   2
Electrical Guidelines . . . . . . . . . . . . . . . . . . 2
Pre-Installation Guidelines .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   2
Preparation of Openings .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   3
Clearances Required Between Corridor Damper Sleeves 
and Ceiling Openings . . . . . . . . . . . . . . . . . 3
Maximum Assembly Table .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   3
Securing the Damper/Sleeve Assembly to Ceiling 
Openings .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   4
Duct to Sleeve Connection  . . . . . . . . . . . . . . 5
Actuator and Temperature Response Device 
Connections . . . . . . . . . . . . . . . . . . . . . . 7
Damper Maintenance . . . . . . . . . . . . . . . . . 8
Damper Troubleshooting.   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   8

®

CFSD Series

1

®

Document 461335

 

Corridor Ceiling Dampers

CFSD-xxx Series 

(with factory installed sleeve and actuator

Installation, Operation and Maintenance Manual

Please read and save these instructions for future reference. Read carefully before attempting to assemble, install, 
operate or maintain the product described. Protect yourself and others by observing all safety information. Failure 
to comply with these instructions will result in voiding of the product warranty and may result in personal injury 
and/or property damage.

Summary of Contents for CFSD-211









Reviews: