![background image](http://html1.mh-extra.com/html/carrier/crecomzr072a01/crecomzr072a01_installation-instructions-manual_2563532002.webp)
2
The EconoMi$er 2 system uses gear-drive technology with a
direct-mount spring return actuator that will close upon loss of
power. Differential dry bulb, enthalpy, and differential enthalpy
sensors are available for field installation. Field-installed CO
2
sensors are available. (See Table 5.)
Optional barometric relief dampers provide natural building
pressurization control. An optional power exhaust system is avail
-
able for applications requiring even greater exhaust capabilities.
The power exhaust set point is adjustable at the EconoMi$er 2
controller.
To see which economizer is used on specific Carrier, Bryant, or
ICP models see Tables 1-3. See Table 4 for package contents and
Table 5 for PremierLink
™
controller sensor usage.
Compliance
EconoMi$er 2 outside air dampers meet the ASHRAE (American
Society of Heating, Refrigeration, and Air-Conditioning
Engineers) 90.1-2016, IECC (International Energy Conservation
Code) 2015, and Title 24 2016 leakage requirements.
Economizers meet California Energy Commission Title 24-2013 /
2016 prescriptive section 140.4 (damper leakage etc.), and when
used with Carrier ComfortLink, RTU Open, PremierLink™,
SystemVu™, or I/O Flex 6126 control systems, meet mandatory
section 120.2.i for Fault Detection and Diagnostic requirements.
Economizers meet ASHRAE 90.1-2013 / 2016 damper leakage
requirements as stated in Section 6.5.1.1.4 and Table 6.4.3.4.3, and
meet 2016 Fault Detection and Diagnosis requirements in section
6.4.3.12 when used with Carrier ComfortLink, RTU Open,
PremierLink, SystemVu, or I/O Flex control systems.
Economizers meet IECC 2012 section C402.4.5.2 and, IECC
2015 sections C403.2.4.3 and C403.3.3.5 for outside air, return air,
and relief air damper leakage requirements, and when used with
Carrier ComfortLink, RTU Open, Premierlink, SystemVu, or I/O
Flex control systems meet IECC 2015 section C403.2.4.7 for
Fault Detection and Diagnostic requirements. Note: IECC 2015
section C403.2.4.7.1 requires differential return air sensor, which
must be ordered separately.
Outside air and return air (volume) dampers are AMCA (Air
Movement and Control Association) rated. Relief air dampers are
also AMCA rated.
Table 1 — Carrier Usage Chart
Table 2 — Bryant Usage Chart
Table 3 — ICP Usage Chart
Table 4 — Package Contents
CARRIER MODEL NUMBER
EconoMi$er
®
2
PART NUMBER
48/50TC 17-24
CRECOMZR072A01
48/50HC 17-20
50TCQ 17, 24
48/50TC 28-30
CRECOMZR073A01
48/50HC 24-28
BRYANT MODEL NUMBER
EconoMi$er®2
PART NUMBER
580J, 558J 17-24
CRECOMZR072A01
581J, 551J 17-20
548J 17-24
580J, 558J 28
CRECOMZR073A01
581J, 551J 24-28
ICP MODEL NUMBER
EconoMi$er
®
2
PART NUMBER
RGS, RAS 181, 183, 210, 213, 240, 243
CRECOMZR072A01
RGH, RAH 181, 210
RHS 181, 240
RGS, RAS 300, 303, 336
CRECOMZR073A01
RGH, RAH 240, 300
EconoMi$er
®
2
PART NUMBER
QTY
CONTENTS
CRECOMZR072A01
1
Damper Assembly With Shroud
1
Upper End Economizer Panel
1
Bottom Panel With Relief Damper
(for vertical only)
1
Bottom Panel #2 (for horizontal only)
1
Side Replacement Panel
(for horizontal only)
3
Filter Supports
3
Central Retainer
2
Side Retainer
1
Hood Top
1
Left Hood Side
1
Right Hood Side
2
Top Diverters
3
Deflector
4
Outside Air Filter Screens
60
Screws #10 — 16 x 7/8 in.
14
Seal Strip (ft) — 1/8 in. x 3/4 in.
CRECOMZR073A01
1
Damper Assembly With Shroud
1
Upper End Economizer Panel
1
Bottom Panel With Relief Damper
(for vertical only)
1
Bottom Panel #2 (for horizontal only)
3
Filter Supports
3
Central Retainer
2
Side Retainer
1
Hood Top
1
Left Hood Side
1
Right Hood Side
2
Top Diverters
3
Deflector
4
Outdoor Air Filter Screens
60
Screws #10 — 16 x 7/8 in.
14
Seal Strip (ft) — 1/8 in. x 3/4 in.