background image

11

Remove the cap from connector C and connect the condensate
drain pipe to drain connector C. (see Fig. 25).

NOTE:  For size 18, the External Condensate lift pump should be
removed (see Fig. 24).

   

 

Connector C 

Fig. 24 −

 

Sizes 9, 12, 18 with External Condensate Lift Pump

   

 

 

Connector C

Fig. 25 −

 

Sizes 24 to 48 with Built−in Condensate Lift Pump

DRAINAGE TEST FOR UNITS WITHOUT A
CONDENSATE LIFT PUMP

Check that the drainpipe is unhindered. Fill the drain pan with 0.5
gallons (2 liter) of water.

Stow tube

Fig. 26 −

 

Units without a Pipe

CONDENSATE LIFT PUMP AND DRAINAGE TEST

Follow these steps to perform the test:

1. Remove the test cover by rotating it counter−clockwise as

shown in Fig. 27.

2. Using a piece of tubing or pipe, fill the condensate lift pump

reservoir with 70 oz. of water (see Fig. 28).

3. Turn the unit ON in cooling mode. The condensate lift

pump comes on. Watch the end of the drain pipe for any
water. It may take some time for the water to travel,
depending on the length of the drain pipe.

4. During this test, check all bends or joints for leakage.

Fig. 27 −

 

Check the Bends and Joints for Leakage

A150675

Fig. 28 −

 

Tube/Pipe Insert

Condensate Lift Pump Maintenance

1. Remove the four screws from the drain pump (sizes 24 to 48).

2. Unplug the pump power supply and water level switch

cable.

3. Detach the pump.

Pump

Fig. 29 −

 

Detach the Pump

Summary of Contents for 40MBDQ series



























Reviews: