caron 7310-22 Operation Manual Download Page 19

Page: 19 / 131

7310 Series Operations Manual

REV E 11-19-19

Page 19 of 131

High concentrations of carbon dioxide can
cause asphyxiation. The use of CO

monitors

and alarms is recommended for areas where
CO

can collect.

The CO

gas supply should be 99% pure and

should not contain a siphon tube. Gas pressure
to the unit must be regulated to 15-20PSI.
Failure to do so could cause tubing to burst.

Connecting a CO

supply (CO2C302)

The CO

supply should be 99% and not have siphon tubes. CO

pressure should be

regulated to 15-20 psi. CO

tank regulators can be purchased through Caron customer

service. Once the cylinder regulator is installed, connect the outlet of the regulator to the
hose barb fitting using the tubing and clamps provided. An inline HEPA filter is provided
to remove any contaminants in the CO

gas supply. Check the connections closely for

leaks.

Summary of Contents for 7310-22




































































































































Search results

Summary of Contents for 7310-22

Reviews:

Related manuals for 7310-22

Brands by name

Popular brands

caron 7310-22, Operation Manual

Search results

Summary of Contents for 7310-22

Reviews:

Related manuals for 7310-22

Brands by name

Popular brands