Carmanah SPEEDCHECK 15 User Manual Download

Page: 57 / 61

Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 |

[email protected]

carmanah.com

SPEEDCHECK-15/18 USER MANUAL

10.0 SERVICE & REPAIR

10.5 Classic Controller Cable Connections (Legacy – without Slow Down)

If your display uses a non-programmable driver board (socketed processor chip and no coin cell battery holders),

proceed as follows:

1. Connect the display cables before connecting the power cable.

a. The 5-pin and 7-pin (1 and 2) connectors go the right LED display.
b. The 3-pin and 7-pin (3 and 4) connectors go to the left LED display.

10.6 Programmable Controller Cable Connections (without Slow Down)

If your display uses a programmable driver board note the following cable connections:

1. Connect the display cables before connecting the power cable.

a. The 5-pin and 7-pin connectors (1 and 2) go the right LED display.
b. The 3-pin and 7-pin connectors (3 and 4) go to the left LED display.

Summary of Contents for SPEEDCHECK 15






























































Search results

Summary of Contents for SPEEDCHECK 15

Reviews:

Related manuals for SPEEDCHECK 15

Brands by name

Popular brands

Carmanah SPEEDCHECK 15, User Manual

Search results

Summary of Contents for SPEEDCHECK 15

Reviews:

Related manuals for SPEEDCHECK 15

Brands by name

Popular brands