Carmanah SPEEDCHECK 15 User Manual Download Page 54

Page: 54 / 61

Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 |

[email protected]

carmanah.com

SPEEDCHECK-15/18 USER MANUAL

10.0 SERVICE & REPAIR

10.2 Accessing SPEEDCHECK-15 Display Boards

Power must be turned off to the sign before proceeding with the following steps.

High risk of LED display board damage if handled while sign is powered.

Mating connectors improperly may cause damage.

A controller board damaged in this way may not be covered by the product warranty.

Lift window retainer clip

Tilt the window forward and lift to

remove

Take note of window alignment

stud for re-installation

Tilt sign to rear

Lift up to remove

Take note of sign retention bolts,

one on each side

Remove the two fasteners

Optional: If present, disconnect

strobe connectors.

Summary of Contents for SPEEDCHECK 15






























































Search results

Summary of Contents for SPEEDCHECK 15

Reviews:

Related manuals for SPEEDCHECK 15

Brands by name

Popular brands

Carmanah SPEEDCHECK 15, User Manual

Search results

Summary of Contents for SPEEDCHECK 15

Reviews:

Related manuals for SPEEDCHECK 15

Brands by name

Popular brands