Carmanah SPEEDCHECK 15 User Manual Download Page 46

Page: 46 / 61

Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 |

[email protected]

carmanah.com

SPEEDCHECK-15/18 USER MANUAL

6.0 SYSTEM CONFIGURATION

6.0 System Configuration

The SpeedCheck radar speed signs are configured using the SpeedCheck Manager software. For more

information on programming and to download the latest version of software please visit

support.carmanah.com

Once your system has been installed and is operational proceed with connecting to the sign via SpeedCheck

Manager. This will require a PC with Bluetooth connectivity. Carmanah assigns default programming based on

your system configuration and may require additional configuration based on your installation requirements.

The following is a few of the features and programming options found within SpeedCheck Manager:

•

Speed adjustments

•

Radar unit of speed (MPH/KPH)

•

Beacon adjustments

•

Operating mode selection

•

Slow Down option toggle

•

System ID, date and time

•

Scheduling

•

Data collection

•

Firmware updating

Updated programmable controllers will require SpeedCheck Manager version 3.0.1.16 or

newer to communicate. Do not continue to use legacy versions of the software known as

DisplayManager or DeviceManager.

Updating firmware on legacy controllers running version 3.47 or older is

not

recommended

Bluetooth Dongle

(if required)

PC (Laptop)

SpeedCheck Manager

Software User Interface

SpeedCheck Sign

Summary of Contents for SPEEDCHECK 15






























































Search results

Summary of Contents for SPEEDCHECK 15

Reviews:

Related manuals for SPEEDCHECK 15

Brands by name

Popular brands

Carmanah SPEEDCHECK 15, User Manual

Search results

Summary of Contents for SPEEDCHECK 15

Reviews:

Related manuals for SPEEDCHECK 15

Brands by name

Popular brands