Carlton SP8018, Owner'S Manual, Page: 47 / 96

SP8018 SERVICING CUTTER WHEEL
TOOTH ARRANGEMENT
•
Inspect pockets, teeth and bolts for damage and
replace as required.
•
When replacing a cutter wheel tooth, replace
the tooth and nut as a set and use anti-seize on
the threads.
•
When replacing teeth and pockets, also replace
the teeth and pockets across from each other
diagonally in order to maintain wheel balance
and prevent vibration.
•
All teeth and pockets are of a specific design
and must be replaced with original
manufacturer’s replacement parts.
Replacement teeth must be carbide tipped.
•
When replacing complete set of teeth, be sure
to duplicate original factory tooth arrangement.
SEE DIAGRAM BELOW.
•
The seating surfaces of the tooth and pocket are
formed, but make sure the tooth is inserted with
the carbide facing the direction of rotation.
•
The pictured view is the engraved side of the
wheel. The wheel is engraved with first (#1)
outside pocket number and an arrow for the
direction of rotation.
•
Outside pocket teeth are Short Plow Bolt Bits.
These pockets are angled and welded in place.
Tip: To prolong tooth life, you can switch teeth
from one outside pocket to a pocket that is the
opposite direction. The cutting edge is the
corner, and this will turn the opposite corner
out for use.
•
These teeth are tightened with nuts. Torque on
nuts is not to exceed 170 ft/lbs.
•
All teeth on cutter wheel sides are Plow Bolt
Bits. When changing these teeth you must
remove both teeth in the same pocket, one on
each side of the wheel. When the nuts are
torqued, the pocket is jammed and the teeth can
only be removed this way.
•
The pocket will receive wear when cutting and
can be switched from one side of the cutter
wheel to the other to prolong life. Remember
the teeth must be replaced in the original
position on each side of the wheel.
C
A R L T O N
O
X
X
O
N O T
L
R A
C
C
A
R
L
TO
N
OX
X
O N O
T
L R
A
C
C
A
R
L
T
O
N
OX
X O
N
O
T
L
R
A
C
C
A
R
L
T
O
N
O
X
X
O
N
O
T
L
R
A
C
C
A
R
L
T
O
N
O
X
X
O
N
O
T
L
R
A C
C A R
L T
O
N
O
X
X
O
N
O
T
L
R A C
C
AR
LT
ON
O
X
X
O
N
O T L R
A C
C
A
R
L T O N
O
X
X O
N
O T
L
R
A
C
C
A
R
L
T
O
N
O X
X O
N
O
T
L
R
A
C
C
A
R
L
T
O
N
O
X
X
O
N
O
T
L
R
A
C
C
A
R
L
T
O
N
O
X
X
O
N
O
T
L
R
A
C
CA
RL
T
O
N
O
X
X
O
N
O
T
L R
A C
LEFT SIDE
#1
#2
#3
#4
#5
#6
#7
#8
#9
#10
#11
#12
#10
#11
C
A
R
L
T
O
N
O
X
X
O
N
O
T
L
R
A
C
C
A
R
L
T
O
N
O
X
X
O
N
O
T
L
R
A
C
CA
RL
T
O
N
O
X
X
O
N
O
T
L
R
A C
CARLTON SP4012 TRIUMPTH MANUAL
NOTE TOOTH PLACEMENT
IN EACH POCKET
ROTATION
Note
: It may
be necessary to use a 1 1/4” hole saw to
remove debris around nut to make tooth removal easier.
34