background image

Page 42

Page 3

3.

General safety advice

Please read carefully!

Target group

Mounting, installation and initial operation of this operator may only be carried out by specialist personnel! 

Qualified and trained specialist personnel are persons

• who have knowledge of the general and special safety regulations,

• who have knowledge of the relevant electro-technical regulations,

• with training in the use and maintenance of suitable safety equipment,

• with sufficient training and supervision by electricians,

• who are able to recognise the special hazards involved when working with electricity. 

• with knowledge regarding applications of the EN 12635 standard (installation and usage requirements).

Warranty

For an operations and safety warranty, the advice in this instruction manual has to be observed. Disregard of these

warnings may lead to personal injuries or material damages. If this advice is disregarded, the manufacturer will not be

liable for damages that might occur. 

Batteries, fuses and bulbs are excluded from warranty.

To avoid installation mistakes and damages to the door and operator, please follow exactly the mounting instructions

provided in this manual. The system may only be used after thoroughly reading the respective mounting and installation

instructions.

The installation and operating instructions are provided to and must be retained by the door system user. 

They contain important advice for operation, checks and maintenance. 

This item is produced according to the directives and standards mentioned in the Manufacturer's Declaration and in the

Declaration of Conformity. The product has left the factory in perfect condition with regard to safety.

Power-driven windows, doors and gates for industrial use must be checked before initial operation, when necessary and

at least once a year by a specialist (with written documentation)! 

Correct use

The operator is meant to be used exclusively to open and close garage doors.

The operator must be used in a dry place.

The maximum push and pull force must be observed.

Door requirements

The door must:

- stand still alone (by balance of springs),

- run smoothly.

Summary of Contents for DC650N III























Reviews: