Carbide 3D HDZ 3.3 Step-By-Step Manual Download Page 21 | Manualshive

Page: 21 / 26

background image

Next place the EZTram mount on the lower front of the Z axis and fit the two provided eccentric spacers to the two
18mm screws. Thread these into the holes of the HDZ.

The side with the groove of the eccentric spacer indicates the lowest point. Lightly tighten the screws so the eccentric
spacers can move (tramming instructions are below).

Fit the two lower 10mm screws and keep these finger tight.

«
...
19
20
21
22
23
...
»

Summary of Contents for HDZ 3.3



























Reviews:

No comments

Related manuals for HDZ 3.3

OKIPAGE 8p Plus

Brand: Oki Pages: 18

Brand: Oki Pages: 107

Brand: Oki Pages: 57

Brand: Xerox Pages: 78

Brand: DPM Pages: 2

Brand: Magicard Pages: 42

Brand: 3D Systems Pages: 29

Brand: Canon Pages: 1154

Brand: Epson Pages: 55

Brand: Epson Pages: 123

Brand: Epson Pages: 261

Brand: Epson Pages: 335

Brand: Epson Pages: 244

Brand: Epson Pages: 260

Epson Stylus Photo P50 Series

Brand: Epson Pages: 2

Brand: WOOSIM Pages: 20

Brand: TH3D Pages: 23

Brand: Brother Pages: 144

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands