Carbide 3D HDZ 3.3 Step-By-Step Manual Download Page 11 | Manualshive

Page: 11 / 26

background image

X Motor Supports

●

4 x M5 25mm supports

There are four threaded holes in the center of the carriage just above the M8 bolts. Insert the 4 x 25mm motor supports
into the 4 holes. Please note these are aluminum. Do not over-tighten them.

When the spacers have been fitted, fit your X motor using the 4 x M5 x 10mm screws provided. As a tip, it's easier to
fit the motor at the same time as re-fitting the belt.

«
...
9
10
11
12
13
...
»

Summary of Contents for HDZ 3.3



























Reviews:

No comments

Related manuals for HDZ 3.3

Brand: Panasonic Pages: 9

Brand: Panasonic Pages: 2

M-Class Mark II

Brand: Datamax Pages: 94

Brand: Oce Pages: 340

Brand: Tektron Pages: 72

Brand: BIXOLON Pages: 59

Brand: SEWOO Pages: 13

ProJet x60 Series

Brand: 3D Systems Pages: 72

PG 2028 SPECIAL

Brand: Olivetti Pages: 104

Brand: Xerox Pages: 2

Brand: Phoenix Contact Pages: 52

Brand: Lexmark Pages: 142

Brand: Pringo Pages: 2

Brand: OKIDATA Pages: 39

Brand: SATO Pages: 2

Brand: Infinite Peripherals Pages: 27

Brand: FARGO electronics Pages: 228

Brand: FARGO electronics Pages: 220

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands