manualshive.com logo in svg

Canon MF724Cdw, Service Manual

Share
Download
Canon MF724Cdw Service Manual Download Page 45

High-voltage

power supply PCBs

Reader unit

D-max

D-half

Color displacement

correction control

Toner cartridge

Laser scanner unit

ITB unit

Color 

displacement/density

sensor

Signal from color

displacement/density signal

Bias

Video signal

Auto-gradation

correction control

● Execution timing

The table below lists the execution timing and duration of each control.

No

.

Executiontiming

Duration

D-max

D-half

Color dis-

placement
correction

Remarks

1 Power-ON

Approx.195sec-
onds

Yes

Yes

Yes

Executed at initial rotation

2 Toner cartridge replacement

Approx.195sec-
onds

Yes

Yes

Yes

Executed at initial rotation

3 Environmentalchanges

Approx.195sec-
onds

Yes

Yes

Yes

Executed after job completionDe-
tected by the environment sensor

4 After the pre-defined counts

printed

Approx.195sec-
onds

Yes

Yes

Yes

Executed after job completion

5 After the pre-defined time

elapsed

Approx.195sec-
onds

Yes

Yes

Yes

Executed after job completion

6 Resumed from sleep (after 8

hours or more)

Approx.100sec-
onds

Yes

Yes

-

Executed after job completion
upon resumed

7 Full correction

Approx.100sec-
onds

Yes

Yes

-

Executed by users

8 Quick correction

Approx.100sec-
onds

Yes

Yes

-

9 Copy image correction

Approx.100sec-
onds

Yes

Yes

-

● Image density correction control (D-max control)

This control is to stabilize the print image density.
The DC controller PCB triggers D-max control under the pre-defined conditions.

1. Measure the density detection patterns for each color on the ITB.

2. Technical Explanation

37

Summary of Contents for MF724Cdw








































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands