manualshive.com logo in svg

Canon MF724Cdw, Service Manual

Share
Download
Canon MF724Cdw Service Manual Download Page 41

ITB

Primary transfer pad

Photosensitive

drum

DC bias

● Step 5: Secondary transfer

Transfer the toner image on the ITB to paper.
The DC positive bias is applied to the secondary transfer external roller to charge the paper positively. By this, the negatively
charged toner image on the ITB is transferred to the paper.

ITB

Secondary 
transfer external roller

Media

ITB drive roller

DC bias

Static charge eliminator

● Step 6: Separation

Separate the paper from the ITB using paper elasticity and curvature of the ITB drive motor. To stabilize the paper delivery and
image quality, use the static eliminator to decay the potential on the back of the paper after image transfer.

ITB

ITB drive roller

Secondary 
transfer external roller

Media

■ Block 4 : Fixing

The toner image is fixed on the paper in this block.

● Step 7: Fixing

This product employs the on-demand fixing method.
By applying pressure and heat on the paper and the toner image on it, the toner is fused to develop the permanent image.

2. Technical Explanation

33

Summary of Contents for MF724Cdw








































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands