manualshive.com logo in svg

Canon MF724Cdw, Service Manual

Share
Download
Canon MF724Cdw Service Manual Download Page 126

External Cover, Internal Cover
Disassembly/Assembly
Procedure

 Removing the Left Cover

■ Procedure

1. To remove the lower claw of the Left Cover, shift the

host machine by 5cm from the base.

2. Remove the Cassette [1].

3. Open the ADF Unit + Reader Unit [2] and the Front

Cover [3].

[1]

DERXW

5 cm

[3]

[2]

4. Remove the 2 screws [2].

[1]

2x

5. While pushing the claw [2] of the Left Cover [1], hold

the top of the host machine, and push the Left Cover

directly upward with your finger on the [A] part of the
Left Cover.

CAUTION:

Do not open [A] part of the Left Cover in the direction
of the arrow when removing the Left Cover; otherwise,
the projection [1] of the Left Cover can be damaged/
broken.

[1]

[1]

[A]

[1]

[A]

1

2

[2]

1x

4. Disassembly/Assembly

118

Summary of Contents for MF724Cdw








































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands