Canon MF724Cdw Service Manual Download Page 165

Page: 165 / 327

Controller System
Disassembly/Assembly
Procedure

Removing the Controller

Cover

■ Preparation

1. Removing the Right Cover.(Refer to

“Removing the

Right Cover” on page 120

)

■ Procedure

1. Remove the Controller Cover [1].

• 9 Screws [2]
• 2 Hooks [3]

[3]

[1]

[2]

Removing the Wireless LAN

PCB (MF728Cdw / 727Cdw /
724Cdw)

■ Preparation

1. Removing the Right Cover.(Refer to

“Removing the

Right Cover” on page 120

)

2. Removing the Controller Cover.(Refer to

“Removing

the Controller Cover” on page 157

)

■ Procedure

1. Remove the Wireless LAN PCB [1].

• 1 Screw [2]
• 1 Flat Cable [3]

[1]

[2]

[3]

Removing the Main Controller

PCB

CAUTION:

When replacing the Main Controller PCB, be sure to
perform the works to be done before replacing the Main
Controller PCB (Refer to

“Before Replacing the Main

Controller PCB” on page 157

) and the works be done

after replacing the Main Controller PCB (Refer to

“After

Replacing the Main Controller PCB” on page 159

■ Before Replacing the Main
Controller PCB

Back up user data (settings, registered data, etc.) and service
mode data for setting and registration after PCB replacement.
Take notes if data is unable to back up.

4. Disassembly/Assembly

157

Summary of Contents for MF724Cdw








































































































































































































































































































































Search results

Summary of Contents for MF724Cdw

Reviews:

Brands by name

Popular brands

Canon MF724Cdw, Service Manual

Search results

Summary of Contents for MF724Cdw

Reviews:

Brands by name

Popular brands