Canon MF724Cdw Service Manual Download Page 176

Page: 176 / 327

2. Remove the Driver PCB [1].

• 11 connectors [2]
• 1 flat cable [3]
• 3 screws [4]
• 1 claw [5]

[5]

[1]

[2]

[4]

[2]

[4]

[3]

11x

Removing the Relay PCB

■ Preparation

1. Removing the Right Cover.(Refer to

“Removing the

Right Cover” on page 120

)

2. Removing the Left Cover.(Refer to

“Removing the

Left Cover” on page 118

)

3. Removing the Rear Upper Cover.(Refer to

“Removing the Rear Upper Cover” on page 123

)

4. Removing the ADF Unit + Reader Unit.(Refer to

“Removing the ADF Unit + Reader Unit” on page
130

)

5. Removing the Right Front Cover.(Refer to

“Removing the Right Front Cover” on page 121

)

6. Removing the Upper Cover.(Refer to

“Removing the

Upper Cover” on page 125

)

■ Procedure

1. Disconnect the flat cable [1] and the 7 connectors

[2].

[1]

[2]

2. Remove the harness guide [1].

• 1 screw [2]
• 1 hook [3]

[2]

[1]

[3]

4. Disassembly/Assembly

168

Summary of Contents for MF724Cdw








































































































































































































































































































































Search results

Summary of Contents for MF724Cdw

Reviews:

Brands by name

Popular brands

Canon MF724Cdw, Service Manual

Search results

Summary of Contents for MF724Cdw

Reviews:

Brands by name

Popular brands