Canon MF724Cdw Service Manual Download Page 149

Page: 149 / 327

5. Remove the harness [1] and the grounding cord [2].

• 1 screw (binding) [3]
• 4 connectors [4]
• 2 Harness Guide [5]

[1]

[3]

[5]

[2]

[4]

6. Remove the 3 screws [1] of the ADF Pickup Feed

Unit.

[1]

7. Close the ADF Upper Cover [1] to remove the ADF

Pickup Feed Unit [2].

[1]

[2]

8. Remove the ADF Upper Cover Unit [1].

• 2 bosses [2]

[1]

[2]

Removing the ADF Pickup

Motor

■ Preparation

1. Remove the ADF Pickup Feed Unit.(Refer to

“Removing the ADF Pickup Feed Unit” on page 140

)

■ Procedure

NOTE:

When removing the ADF Pickup Motor, it is not necessary
to remove the ADF Upper Cover Unit described in the
previous step.

4. Disassembly/Assembly

141

Summary of Contents for MF724Cdw








































































































































































































































































































































Search results

Summary of Contents for MF724Cdw

Reviews:

Brands by name

Popular brands

Canon MF724Cdw, Service Manual

Search results

Summary of Contents for MF724Cdw

Reviews:

Brands by name

Popular brands