Canon iPF830 Series Basic Manual Download Page 97

Page: 97 / 146

Important

•

Do not force the roll paper into alignment with the Paper Alignment Line (b). This may prevent the paper
from being advanced straight.

•

If you pull out too much of the roll, an excessive amount will be cut away.

Close the Top Cover.

Turn the printer on. (See "Turning the Printer On and Off.")

➔

User's Guide

The roll is now advanced. After it is finished being advanced, you can resume printing.

Note

•

You can ensure that the edge is cut neatly by selecting

Paper Cutting

in the printer menu.

(See "Specifying the Cutting Method for Rolls.")

➔

User's Guide

Clearing a Jammed Sheet

If a sheet jams, follow the steps below to remove it.

Turn the printer off. (See "Turning the Printer On and Off.")

➔

User's Guide

Open the Top Cover.

If the Carriage is out, move the Carriage out of the
way, away from the paper.

iPF830 Series

Clearing a Jammed Sheet

Basic Guide

Troubleshooting

Problems Regarding Paper

Summary of Contents for iPF830 Series



















































































































































Search results

Summary of Contents for iPF830 Series

Reviews:

Brands by name

Popular brands

Canon iPF830 Series, Basic Manual

Search results

Summary of Contents for iPF830 Series

Reviews:

Brands by name

Popular brands