manualshive.com logo in svg

Canon iPF830 Series, Basic Manual

Share
Download
Canon iPF830 Series Basic Manual Download Page 21

Handling sheets

Handling sheets

Loading Sheets in the Printer ..........................................................................................................................

21

Removing Sheets ............................................................................................................................................

23

Loading Sheets in the Printer

Loading Sheets in the Printer

Follow these steps to load sheets in the printer.

Important

•

Paper that is wrinkled or warped may jam. If necessary, straighten the paper and reload it.

•

Load the paper straight. Loading paper askew will cause an error. (See "Paper loaded askew..")

➔

P.127

Note

•

Before loading sheets, make sure the printer is clean inside the Top Cover and around the Ejection Guide. If these
areas are dirty, we recommend cleaning them in advance.  (See "Cleaning Inside the Top Cover.")

➔

P.47

•

Store unused paper in the original package, away from high temperature, humidity, and direct sunlight.

1

Select sheets as the paper source.

•

If a print job was received
Sheets are automatically selected, and the media type and size specified by the print job are shown on
the Display Screen.
Press 

▲

 or 

▼

 to select 

Load Paper

, and then press the 

OK

 button.

•

If no print job was received

1.

 

Press the 

Load

 button.

2.

Press 

▲

 or 

▼

 to select 

Cut Sheet

, and then press the 

OK

 button.

Note

•

If any paper has been advanced that will not be used, a message is shown requesting you to remove it.
Press 

▲

 or 

▼

 to select 

Yes

, and then press the 

OK

 button. Remove the paper and go to the next step.

2

 

Lift the Release Lever and open the Top Cover.

 

 

iPF830 Series

                                                                                                                                                                      

Loading Sheets in the Printer

Basic Guide

                                                                                                                                                                                                                       

   

Handling Paper

Handling sheets

21

 

Summary of Contents for iPF830 Series



















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands