manualshive.com logo in svg

Canon iPF830 Series, Basic Manual

Share
Download
Canon iPF830 Series Basic Manual Download Page 75

Reinstalling the Printer

Reinstalling the Printer

The basic workflow for reinstalling the printer is as follows.
For detailed instructions, see the Setup Guide.

Assemble the stand

1

Referring to the Printer Stand Setup Guide, assemble the Stand.

Caution

•

The Stand must be assembled by at least two people on a flat surface. Attempting assembly by yourself
poses a risk of injury or bending the Stand.

•

When assembling the Stand, lock the casters. In addition, always unlock the casters before moving the
assembled Stand. Attempting to move the stand when the casters are locked poses a risk of injury or
damage to the location site.

Install the printer

1

 

Mount the printer on the assembled Stand and tighten
the screws firmly.

Caution

•

Moving the printer requires at least six people, holding it on both sides. Be careful to avoid back strain
and other injuries.

•

When moving the printer, firmly grasp the Carry-
ing Handles (a) under each side. The printer may
be unsteady if you hold it at other positions,
which poses a risk of injury from dropping the
printer.

a

 

 

iPF830 Series

                                                                                                                                                                                 

Reinstalling the Printer

Basic Guide

                                                                                                                                                                                                                       

   

Printer Relocation

Preparing to Transfer the Printer

75

 

Summary of Contents for iPF830 Series



















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands