Canon imageRUNNER C1335 Series, Service Manual

Page: 532 / 607

8
8
8-93
8-93
Service Mode > COPIER > OPTION > DSPLY-SW
Service Mode > COPIER > OPTION > DSPLY-SW
■
DSPLY-SW
COPIER> OPTION> DSPLY-SW
T-LW-LVL Dspl timing of toner level warning mssg
Details To set the threshold value of residual toner in the toner bottle.
When the residual toner level becomes lower than the threshold, a
warning message of “Toner is low. Replacement not yet needed.” is
displayed on the Control Panel.
Use case • Upon user’s request
• At the timing that the service engineer visits to the user, etc.
Adj/set/operate method Enter the setting value, and then press Start key.
Caution
When setting a value smaller than the initial value, absence of toner
may be displayed before toner level warning message.
Display/adj/set range 5 to 100
Unit 1 %
Default value It differs according to the location.
Related service mode COPIER> OPTION> DSPLY-SW> TNR-WARN
TNR-WARN ON/OFF of toner level warning message
Details To set ON/OFF of toner warning display.
When 1 is set, toner warning is not displayed until the toner runs out.
Use case When preferring not to display warning until the toner runs out
Adj/set/operate method 1) Enter the setting value, and then press Start key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Display, 1: Hide
Default value JP:0, USA:1, EUR:0, AU:0, CN:0, KR:0, TW:0, ASIA:0
Related service mode COPIER> OPTION> DSPLY-SW> T-LW-LVL
Related UI menu
Preferences> Display Settings> Display Remaining Toner Error Message
Supplement/memo Display of the warning screen can be switched by Settings/Registration>
Preferences> Display Settings> Display Remaining Toner Error
Message.
WT-WARN Dspl/hide of Wst Tonr Cntner prep mssg
Details To set whether to display the preparation warning message of the Waste
Toner Container on the status area of LUI.
Use case When there is no need to notify the preparation timing of the Waste
Toner Container to the user
Adj/set/operate method 1) Enter the setting value, and then press Start key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Hide, 1: Display
Default value 1
COPIER> OPTION> DSPLY-SW
DF-DSP Dspl/hide DADF Roll counter initial scrn
Details To set whether to display the DADF Roller on the counter initialization
screen in Settings/Registration.
Use case When the user does not replace the parts
Adj/set/operate method Enter the setting value, and then press Start key.
Display/adj/set range
0 to 1
0: Hide, 1: Display
Default value 1
2TR-DSP Dspl/hide Sec Trn Out Rol cntr init scrn
Details To set whether to display the Secondary Transfer Outer Roller on the
counter initialization screen in Settings/Registration.
Use case When the user does not replace the parts
Adj/set/operate method Enter the setting value, and then press Start key.
Display/adj/set range
0 to 1
0: Hide, 1: Display
Default value 0
ITB-DSP ON/OFF of init after ITB rplce: Set/Reg
Details To set whether to display “ITB” on Initialization screen after replacing
parts in Settings/Registration.
When allowing the user to replace the ITB, set 1.
Use case When allowing the user to replace the ITB
Adj/set/operate method Enter the setting value, and then press Start key.
Display/adj/set range
0 to 1
0: OFF, 1: ON
Default value 0
Related UI menu Adjustment/Maintenance> Maintenance> Initialize After Replacing
Parts> ITB
FXU-DSP ON/OFF init after Fx Ass’y rplce:Set/Reg
Details To set whether to display “Fixing Unit” on Initialization screen after
replacing parts in Settings/Registration.
When allowing the user to replace the Fixing Assembly, set 1.
Use case When allowing the user to replace the Fixing Assembly
Adj/set/operate method Enter the setting value, and then press Start key.
Display/adj/set range
0 to 1
0: OFF, 1: ON
Default value 1
Related UI menu Adjustment/Maintenance> Maintenance> Initialize After Replacing
Parts> Fixing Unit
T-8-40