Canon ImageRunner 600 Service Manual Download Page 89

Page: 89 / 875

3-16

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A

CHAPTER 3 ORIGINAL EXPOSURE SYSTEM

Figure 3-A501

Figure 3-A502

[1]

[3]

[1]

[4]

[2-1]

[2-2]

[6]

[5]

No. 1 Mirror Mount

Removing the Scanning Lamp/
Scanning Lamp Heater

1) Remove the right glass retainer [2-1] and

the left glass retainer [2-2]; then, detach
the copyboard glass [3] and the scanning
map cover [4].

2) Remove the four screws [5], and detach

the scanning lamp inside cover [6].

Summary of Contents for ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ImageRunner 600

Reviews:

Canon ImageRunner 600, Service Manual, Page: 89 / 875

Search results

Summary of Contents for ImageRunner 600

Reviews: