Canon ImageRunner 600 Service Manual Download Page 385

Page: 385 / 875

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

9-9

CHAPTER 9 EXTERNALS/AUXILIARY MECHANISMS

Sequence of Operations

The fans operate as follows, ones controlled according to the state of the printer and ones

controlled by the state of the scanning lamp:

(FM3, FM11, and FM12 operate based on the state of both the printer unit and the scanning

lamp, and the control mechanism for higher speed is used for the chart.)

Fans Operating According to the State of the Printer Unit

Figure 9-403

Fans Operating According to the State of the Scanning Lamp

Figure 9-404

Control panel
switch ON

Main power
switch ON

Primary charging
assembly fan (FM1)

Drum fan (FM8)
Pre-transfer charging
assembly fan (FM10)

Feeding fan (FM7)

Scanner cooling fan
(FM3)

Fixing assembly heat
discharge fan (FM2)

Laser driver cooling
fan (FM5)

Separation fan (FM13)

Power supply cooling
fan 1/2 (FM11, FM12)

Laser scanner motor
cooling fan (FM14)

De-curling fan (FM6)

Warm-up

Printer unit

Initialmultiple rotation

Standby

Copying

Pre-heating

Door open

Jam

Error

After copying

;;;;;;;

yyyyyyy

;;;;;;;

yyyyyyy

;;;;;;;

yyyyyyy

;;;;;;;

yyyyyyy

;;;;;;;

yyyyyyy

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

yyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy

;;;;;;;

yyyyyyy

;;;;

yyyy

;;;;;;;;;;;;;;;;;;;;;;;;;;;

yyyyyyyyyyyyyyyyyyyyyyyyyyy

;;;;;;;;;;;;;;;;;;;;

yyyyyyyyyyyyyyyyyyyy

;;;;;;;;;;;;;;;;;;;;;;;;;;;

yyyyyyyyyyyyyyyyyyyyyyyyyyy

;;;;;;;;;;;;;;;;;;;;

yyyyyyyyyyyyyyyyyyyy

;;;;;;;;;;;;;;;;;;;;;;;;;;;

yyyyyyyyyyyyyyyyyyyyyyyyyyy

;;;;;;;

yyyyyyy

;;;;;;;

yyyyyyy

;;;;;;;

yyyyyyy

;;;;;;;

yyyyyyy

;;;;;;;;;;;;;;;;;;;

yyyyyyyyyyyyyyyyyyy

;;;;;;;;

yyyyyyyy

;;;;;;;;;;;;;;;;;;;;;;;;;;;

yyyyyyyyyyyyyyyyyyyyyyyyyyy

;;;;;;;

yyyyyyy

;;;;;;;

yyyyyyy

15 min

: full speed. : half speed.

Warm-up: Until the temperature of the fixing assembly reaches 195˚C.
Intial multiple rotation: After the temperature of the fixing assembly has

reached 200˚C until potential control ends.

Scanning lamp cooling fan
(FM3)

Power supply cooling fan
1/2 (FM11, FM12)

Stream reading fan (FM4)

Inverter cooling fan (FM9)

Scanning lamp

Off

Pre-heating

Error

;;;;;;;;;;

yyyyyyyyyy

;;;;;;;;;;

yyyyyyyyyy

;;;;;;;;;;;

yyyyyyyyyyy

;;;;;;;;;;;;;;;;;;;;;;

yyyyyyyyyyyyyyyyyyyyyy

Main power
switch ON

;;;;;

yyyyy

: full speed. : half speed.

Summary of Contents for ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ImageRunner 600

Reviews:

Canon ImageRunner 600, Service Manual, Page: 385 / 875

Search results

Summary of Contents for ImageRunner 600

Reviews: