Canon ImageRunner 600 Service Manual Download Page 441

Page: 441 / 875

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

9-65

CHAPTER 9 EXTERNALS/AUXILIARY MECHANISMS

Figure 9-F701

[1]

[2]

[1]

DC Controller PCB

1) Remove the rear cover.
2) Open the system box assembly.
3) Disconnect the 19 connectors on the PCB,

and remove the four screws [1]; then, de-
tach the DC controller PCB [2].

Summary of Contents for ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ImageRunner 600

Reviews:

Canon ImageRunner 600, Service Manual, Page: 441 / 875

Search results

Summary of Contents for ImageRunner 600

Reviews: