Canon ImageRunner 600 Service Manual Download Page 472

Page: 472 / 875

10-24

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

CHAPTER 10 SIDE PAPER DECK

Figure 10-A306

Figure 10-A307

Removing the Rear Cover

1) Release the deck, and remove the six

screws [1]; then, detach the rear cover [2].

Removing the Right Cover

1) Remove the three screws [1], and move

the right cover [2] to the front; then, re-
move it toward the rear.

[1]

[2]

[1]

Summary of Contents for ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ImageRunner 600

Reviews:

Canon ImageRunner 600, Service Manual, Page: 472 / 875

Search results

Summary of Contents for ImageRunner 600

Reviews: