Canon ImageRunner 600 Service Manual Download Page 406

Page: 406 / 875

9-30

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

CHAPTER 9 EXTERNALS/AUXILIARY MECHANISMS

Figure 9-B701

[2]

[1]

[2]

Figure 9-B703

Figure 9-B702

[3]

[4]

[6]

[7]

[5]

Control Panel

Removing the Control Panel

1) Remove the standard white plate. (See

Figures 3-D511 through -D513.)

2) Remove the copyboard glass and the con-

trol panel middle cover.

3) Remove the two screws [1], and detach

the face plate [2].

4) Remove the two screws [3], and detach

the delivery tray unit [4].

5) Remove the two screws [5], and detach

the upper right cover [7] while keeping
the toner cartridge cover [6] open.

Summary of Contents for ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ImageRunner 600

Reviews:

Canon ImageRunner 600, Service Manual, Page: 406 / 875

Search results

Summary of Contents for ImageRunner 600

Reviews: