Canon ImageRunner 600 Service Manual Download Page 444

Page: 444 / 875

9-68

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

CHAPTER 9 EXTERNALS/AUXILIARY MECHANISMS

Figure 9-J701

[1]

Figure 9-K701

[1]

[2]

Relay PCB

1) Remove the lower left cover.
2) Disconnect the connector from the relay

PCB, and remove the PCB spacer to de-
tach the relay PCB [1].

MFC PCB

1) Remove the rear cover.
2) Remove the system box.
3) Remove the 16 screws [1], and detach the

system cover 1 [2].

Summary of Contents for ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ImageRunner 600

Reviews:

Canon ImageRunner 600, Service Manual, Page: 444 / 875

Search results

Summary of Contents for ImageRunner 600

Reviews: