Canon ImageRunner 600 Service Manual Download Page 818

Page: 818 / 875

CHAPTER 13 TROUBLESHOOTING

13-230

CANON imageRUNNER 600 REV.1 JAN. 2000 PRINTED IN U.S.A.

OPTION Settings Mode

Figure 13-F801 shows the screen under COPIER>OPTION and its items.

Figure 13-F801 Screen under Items COPIER>OPTION

Display

I/O

Adjust

Option

Test

Counter

Function

BODY

USER

CST

ACC

Note:

The new setting for each item of OPTION will be stored in memory when the main power
switch is turned off and then on.

Summary of Contents for ImageRunner 600































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ImageRunner 600

Reviews:

Canon ImageRunner 600, Service Manual, Page: 818 / 875

Search results

Summary of Contents for ImageRunner 600

Reviews: