Canon 3300 Series Manual Download Page 67 | Manualshive

Page: 67 / 235

Canon 3300 Series Manual Download Page 67

2

Communications Using the Subaddress (Subaddress)

2-35

Basic F

ax Usage

2

Press “Subaddress” and enter the other party’s subaddress

press “Password” and enter the other party’s password using

-

(numeric keys)

press “OK.”

If the other party did not set an RX password in the target subaddress, you do not need to
enter a password.

The specified mode is set and the display returns to the Fax Basic Features screen.

3

Specify the sending destination, and press

(Start).

To specify destinations, see ‘Various Dialing Methods,’ on p. 2-19.

NOTE
•

If you specify the remote machine using One-touch Speed Dialing or Coded Speed Dialing in
which a subaddress and RX password are registered, the registered subaddress and RX
password are used, even if you set a subaddress and RX password with this function.

Index.book Page 35 Thursday, May 24, 2001 12:30 AM

«
...
65
66
67
68
69
...
»

Summary of Contents for 3300 Series












































































































































































































































Reviews:

No comments