Canon 2000 Service Manual Download Page 278

Page: 278 / 381

FACSIMILE SYSTEM

6–6

The following describes the functions of the NCU board divided into basic

functions.

Fig. 6-4 Block Diagram of NCU Board Functions

3.1

Off-hook Detection

The off-hook of the telephone connected to the facsimile is detected when

the telephone is in standby state or during facsimile communications. The

circuit’s built-in telephone set is designed so that terminals to be connected

with the telephone line have an infinite (DC) resistance when the handset

is placed down (on-hook) and several hundred ohms of DC resistance

when it is lifted (off-hook).

3.2

Formation of DC Loop

As a DC voltage (0 to several tens of volts) is supplied across L1 and L2 at

all times from the

exchange

, DC current flows between the facsimile and

the exchange when the telephone becomes off-hook or when the CML

relay

turns ON. This current flow is called “formation of DC loop.”

By formation of this DC loop, the exchange recognizes the response from

the telephone (reception terminal), and performs connection of the tele-

phone line to enable communications. For this reason, the DC loop must

be retained during facsimile communications or during a conversation on

the telephone.

In Fig. 6-5, DC voltage is supplied to the telephone as DC voltage is being

supplied to terminals L1 and L2 on the facsimile from the exchange and

L1 and L2 are connected internally on the NCU board. Yet, as the HS is

MODEM

T21

T12

T11

T22

System

controller

Off-hook

detection

Detection of CI

H relay

Line signal

monitor

Exchange

CML relay

S relay

P relay Formation of

DC loop

2-wire/4-wire

conversion

Vref

generation

NCU

board

SCNT

board

Summary of Contents for 2000





























































































































































































































































































































































































Search results

Summary of Contents for 2000

Reviews:

Related manuals for 2000

Brands by name

Popular brands

Canon 2000, Service Manual

Search results

Summary of Contents for 2000

Reviews:

Related manuals for 2000

Brands by name

Popular brands