Canon 2000 Service Manual Download Page 199

Page: 199 / 381

5–57

ït

çi

G3 FACSIMILE COMMUNICATIONS

coded data on a convolutional coder is called the “coding constraint

length,” and is two in the case of the coder in Fig. 5-49.

Fig. 5-49 Convolutional Coder

Here, let’s describe the regularity of the coded output data on the input data

on a convolutional coder. In the coder in Fig. 5-49, the combinations of

two bits 00, 10, 01 and 11 currently stored in the shift register can each be

expressed by four states A, B, C and D. At this time, the relationship

between these four states and one bit of input data can be expressed as the

shift in states in Fig. 5-50. For example, in this figure, if the state of the

shift register is A and 0 is input as the input data, coded data 00 is output,

and the state remains at A. When 1 is added to the input data, coded data

11 is output which means that the state will shift to state B. In other words,

from state A the state shifts only to state A or to state B.

The shift in states of other states B, C and D also have the same nature.

Fig. 5-50 Shift in States of Convolutional Coder

In Fig. 5-50, when input data is “0” for each of the internal states A, B, C

and D of the shift register, the shift in state is expressed by the solid line,

and when input data is “1”, the shift in state is expressed by the dotted line.

The data of two bits shown on the solid line or dotted line shows the coded

[2]

[1]

Coded
output data

The sum of modulo 2 is taken.

Input data

Shift register

The sum of modulo 2 is taken.

Ser

ialization

circuit

Shift register states

A: 00
B: 10
C: 01
D: 11

: Shift when input

data is "0"

: Shift when input

data is "1"

Summary of Contents for 2000





























































































































































































































































































































































































Search results

Summary of Contents for 2000

Reviews:

Related manuals for 2000

Brands by name

Popular brands

Canon 2000, Service Manual

Search results

Summary of Contents for 2000

Reviews:

Related manuals for 2000

Brands by name

Popular brands