Canon 2000 Service Manual Download Page 170

Page: 170 / 381

G3 FACSIMILE COMMUNICATIONS

5–28

4.3.6 Effect of MR coding scheme

The table shows the size of compressed data by the MR coding scheme and

the MH coding scheme.

In the document example in Fig. 5-23, the compression ratio becomes

about 71% as shown in the following formula by the MR coding scheme

compared with the MH coding scheme.

Data size by MR coding / Data size by MH coding = 278/390 = 0.7128 ...

Approx. 71%

In actual coding of the document, the compression ratio becomes between

about 70% to 90% depending on the pattern of the document and the

verti-

cal scanning

line density.

4.4

MMR Coding Scheme

MMR stands for Modified Modified READ, and somewhat resembles the

MR coding scheme. By MMR, coding starts from a white line, and there

are no restrictions in parameter K. In other words, the initial line is taken to

the be the reference line, and only differences from the previous line are

coded by MR right until the end of the page. For this reason, as a condition

for use of MMR, MMR is limited to instances where error-free communi-

cations can be assured. So, with G3 facsimiles, MMR is used only in com-

binations with the ECM (Error Correction Mode) of

ITU-T

described later.

Table 5-7 Comparison of the Effect by MR Coding and MH Coding

MR coding

MH coding

1st line

43 bits

41 bits

2nd line

14 bits

29 bits

3rd line

56 bits

4th line

34 bits

54 bits

5th line

55 bits

54 bits

6th line

22 bits

54 bits

7th line

24 bits

48 bits

8th line

30 bits

54 bits

Total

278 bits

390 bits

Summary of Contents for 2000





























































































































































































































































































































































































Search results

Summary of Contents for 2000

Reviews:

Related manuals for 2000

Brands by name

Popular brands

Canon 2000, Service Manual

Search results

Summary of Contents for 2000

Reviews:

Related manuals for 2000

Brands by name

Popular brands