manualshive.com logo in svg

CAMSO 24D18C, Service Manual, Page: 37 / 106

Share
Download
CAMSO 24D18C Service Manual Download Page 37

3 - Midroller Wheel Seal And Bearing Removal And Installation

35

STEP  22

Carefully install the hub (1) assembly on the axle
without dislodging the inner bearing and face seal
until the face seals make contact. Hold the hub
assembly in the position for Steps 23 through 25.

NOTE:

On models before TRE0216003 the bearing

is a press fit and will require the hub and bearing
assembly to be pressed on the axle if not heated in
Step 17.

STEP  23

Install the outer bearing cone (1). 

IMPORTANT:

The hub MUST be held in place with

slight pressure against the face seals until the lock
nut is installed in Step 25.

STEP  24

Install the locking washer (1).

STEP  25

Use the Locknut Socket (2P-0085) to install the lock
nut (1) and tighten to 150 N•m (112 ft-lb) to fully seat
the bearings. Loosen the locknut 1/2 turn and tighten
to 38 N•m (28 ft-lbs). Rotate the hub five times and
check nut for correct torque.

cp0498

1

cp0497

1

cp0496

1

1

cp0495

1

Summary of Contents for 24D18C











































































































Reviews:

No comments