![background image](http://html.mh-extra.com/html/campagnola/speedy/speedy_use-and-maintenance-manual_488413029.webp)
Use and maintenance manual – Translation of
original Instruction. : 04 date 16/09/2021
Page 29
•
Do not put the shear, the battery or the charger into any liquids.
•
Do not insert nails, do not hammer or step on or throw or cause any other damage to the battery.
•
Do not use the battery if it is damaged or deformed.
•
Do not carry out welding on the battery.
•
Do not reverse the polarity of the connections or excessively discharge the battery.
•
Do not connect the battery to car chargers or cigarette lighter sockets.
•
Do not use the battery for devices which are other than those indicated by the Manufacturer.
•
Do not come into direct contact with lithium battery cells.
•
Do not put the battery into microwaves or containers with high temperatures or high pressures.
•
Do not use the battery in case of fluid loss.
•
Do not use the battery in an electrostatic environment (above 64V)
•
Do not use the battery if it is corroded, visibly deformed or unpleasantly smelly.
•
If your skin or clothes come in contact with the battery fluid, rinse them immediately with water.
•
Keep the battery fully charged when the shear is not used for long periods.
•
Always disconnect the charger from the electrical network when the batteries are charged up.
•
Always disconnect the batteries from the charger after recharging.
4.3 Packing and transport
The unit is packaged by the Manufacturer and sent to the dealer in a carton box.
The handling of loads must be carried out in compliance with the current workplace safety rules. Use the box for
storing the tool for medium or long periods or for sending the packed product to a Service Point for repairs.
5.1 Tool starting
Before operating the tool, always wear protective clothing.
•
Hold the handle with one hand. Press the ON/OFF button (5) with the other hand.
•
The tool is ready for use.
•
Use the tool only for the purposes described in par. "Product description". Any other use could cause injuries.
•
Operate the tool only when it is inserted among the branches. Any improper use causes greater tool wear and
battery consumption.
5.1.1 Precautions for the use
•
Do not cut either branches with a diameter over 25 mm or metals, or stones, or any object which is not a plant. When
the blades get worn or damaged, replace them.
•
Rinse the shear by means of a clean and dry cloth. Do not use any petrol or solvents.
•
To rinse the shear, do not use abrasive degreasers or containing solvents.
•
For a proper shear operation follow the instructions. In case of damage do not use the shear, the battery and its charger.
•
It is dangerous to use a shear which does not work properly.
•
Always remove the battery before any operation of adjustment or parts replacement or before storing it at the end of
the work session. This allows to reduce the residual risks due to an involuntary tool activation.
•
The blades must be closed when the shear does not work.
•
The shear must be operated following the instructions and the way of use indicated in this manual, taking into consid-
eration the environment and the kind of work to carry out. It is recommended not to use the pruning shears in case of
poor psychophysical skills or in situations which are different from the indicated ones, as it could be very dangerous.
•
After each use remove the residues from the blades and put the LUBE SPRAY GREASE lubricant recommended by
the Manufacturer. These operations guarantee that the blades are kept in good conditions, reduce wear and extend
the lifespan of the shear as well as of the blades.
5.2 Stopping the shear
The shear must be switched off at the end of each work session, therefore:
•
Close the blades,
•
Put the ON/OFF button (5) in “OFF” position,
•
Remove the battery,
•
Carefully put the shear into its packaging.