5 – USE OF THE TOOL
47 - 120
electronic unit and the battery
The shear is not power supplied
Check the connection between the
electronic unit and the shear
The shear is not powerful enough.
Flat battery (1).
Re-charge the battery (1).
Worn-out cutting blade (14)..
Sharpen the blade (14) or replace it
if it is too worn out.
Excessively tightened blade pin
(29).
Carry out the service procedure
(see par. 5.1).
Excessive battery (1) consumption.
Worn-out cutting blade (14).
Sharpen the blade (14) or replace it
if it is too worn out.
The shear does not close the
blades, and the display shows the
indication STOP followed by
MAX_TEMP
Motor overheating due to cuts of too
thick branches
Wait till the temperatures decreases
at least 5°C before starting the
cutting operations again
The shear does not close the
blades, and the display shows the
indication STOP followed by
OVERLOAD
Inner overheating has stopped the
shear
Wait few seconds and then go on
cutting mainly thin branches, so that
the heat becomes lower than
protection threshold
The shear does not close the
blades, and the display shows the
indication STANDBY
The trigger (12) is locked
Pull the trigger (12) 3 times
The shear does not close the
blades, and the display shows the
indication RESTART
The shear is in safety block
Re-start the electronic box by
means of the selector (19)
The battery cannot be switched on
or off
The switch (8) has been pressed too
quickly
Keep the switch (8) pressed for
more than 1 second
6
- MAINTENANCE
6.1 Routine maintenance
WARNING!
•
Before any routine maintenance operations, turn the selector (19) anti-clockwise and put the selector (8)
in position 0 to switch both off.
•
All maintenance operations which are not dealt with in this manual shall only be carried out by
Authorized Service Points.
Ordinary maintenance operations can be carried out by the operators.
6.1.1 General
Before any ordinary maintenance operation:
• Turn the selector (19) anti-clockwise and put the selector (8) in position 0 to switch both off.
• Wear protective gloves.
IMPORTANT!
6.1.2 Blade sharpening
•
After the first ½ hour of use, re-sharpen the cutting blade (14) with the stone supplied.
•
Every 3 hours of use, sharpen the blade (14) cutting edge slightly.
•
To carry out a perfect blade sharpening:
a) Keep a sharpening angle of 45° from the cutting blade (14)
b) Follow the cutting edge from the inner to the outer part
c) Repeat the operation 8/9 times
WARNING!
Do not sharpen neither the anvil (16) nor the rear part of the cutting blade (14).
Summary of Contents for Mastiff
