background image

   

Operation:   

The    CALMAG    YORKSHIRE    LTD    CALULTRA    system    comes    with    a    feature    laden    control    system    that   

incorporates   both   the   lamp   driver   (ballast)   and   control   features   in   one   modular   panel.   CAUTION:   Prior   to   

performing   any   maintenance   on   your   UV   system,   you   must   always   disconnect   the   power   (DO   NOT   SIMPLY   

USE   THE   SWITCH   ON   THE   FRONT   OF   THE   CONTROLLER).   

CALULTRA

   

Control   Panel   

The   control   panel   features   a   power   factor   corrected   and   constant   current   lamp   
driver.   Simplistic   in   operation,   the   panel   features   an   LED   display   for   remaining   
lamp   life,   total   running   hours,   audible   and   visual   lamp   failure,   remote   on   and   
solenoid   ready.   When   the   UV   lamp(s)   is/are   on,   the   second   LED   box   will   read   
“ON”.   When   the   UV   lamp(s)   is/are   not   on,   the   LED   box   will   read   “OFF”   and   an   
audible   alarm   will   sound.   Please   Note:   If   the   LED   reads   “OFF”   and   the   alarm   is   
sounding    then    the    water    from    the    system    should    NOT    be    consumed.    If    any   
water   does   pass   through   the   UV   system   during   this   period,   please   follow   the   
disinfection    procedure    as    outlined    in    this    manual    before    the    water    is   
consumed.   It   should   also   be   noted   that   on   the   CALULTRA   system   even   though   
this   system   does   have   a   visual   and   audible   warning   built   into   the   controls,   the   
LED   reading   “ON”   does   not   necessarily   indicate   that   the   water   coming   from   this   
system   is   in   fact   potable   (safe   to   drink).   This   system   does   not   measure   the   level   
of    disinfection;    it    simply    measures    the    “ON-­‐OFF”    status    of    the    lamp.    For    a   
constant   reassurance   of   safe   water   quality   you   should   consider   the   CALULTRA   
upgrade   with   a   UV   sensor   (you   can   also   add   the   optional   RS-­‐RUV   sensor   on   all   
CALULTRA    systems).    Please    have    your    water    checked    for    microbiological   
contaminants   on   a   regular   basis.   

   

CALULTRA   3-­‐Position   Switch   

The   control   panel   features   a   3-­‐position   user-­‐selectable   switch.   This   switch   is   NOT   a   power   switch   and   it   
should   be   noted   that   once   the   control   panel   is   plugged   into   an   electrical   outlet,   the   unit   is   powered   and   
considered   “ON”.   The   switch   functions   as   follows:   

ON”   position   –   Power   is   supplied   to   the   lamp(s)   and   the   controller   will   read   
“ON”   on   the   lower   LED   display   on   units   without   a   UV   sensor   installed   and   will   
read    the    intensity    (or    UV    output)    on    units    with    a    UV    sensor    installed.    Please   
note    that    when    first    starting    the    lamp(s),    the    system    will    cycle    through    a   
declining   numerical   sequence   while   the   lamp(s)   reaches   full   power.   

   

OFF”   position   –   Power   is   NOT   supplied   to   the   lamp(s)   and   the   lamp(s)   will   be   
off.   The   controller   will   read   “OFF”   on   the   lower   LED   display.   

Page

14

Summary of Contents for CALULTRA 132

























Reviews: