background image

31-2000815 Rev. 0

9

Installation

2

  MOVE THE RANGE INDOORS

1 .   Tilt the range forward on the skid .

2 .   Lift the toekick out of the foam base .

3 .   Drive the blade of the hand-truck beneath the foam 

block .

IMPORTANT:

 Do not remove the base foam block while 

the hand-truck is in use . Place the hand-truck blade 

underneath the base foam block and transport the range 

to the final location .

4 .   Attach the hand-truck straps around the unit .
  

IMPORTANT:

 Place the hand-truck straps below the 

oven door handles. To avoid damaging the side panels, 

place a pad between the hand-truck and the range .

5 .   Tilt the range to lower the hand-truck wheels off the 

skid .

6 .   Place the appliance runners on the floor at the left 

and right sides in front of the opening .

  

IMPORTANT:

 The runners provide a surface for 

rolling the range into the final position and will protect 

the floor finish . The runners must be removed before 

leveling the range .

7 .   Move the range indoors . Position the range in front of 

the installation location, onto the runners.

Toekick

Toekick

Insert Blade Under 

the Foam Block

You may need to remove 

the front of the foam block 

to fit through the doorway .

Hand-Truck 

Straps Below 

Oven Door 

Handles

Range 

Opening

Runners 

for Rolling 

the Range 

into 

Position

Summary of Contents for C2Y366





















Reviews: