manualshive.com logo in svg

Caen ELS CT-BOX, Quick Start Manual

Share
Download
Caen ELS CT-BOX Quick Start Manual Download Page 14

CT-BOX Viewer – Quick Start Guide 

 
14 
 

 

3.

 

CT-BOX Firmware update 

 
 
 
The  firmware  of  the  CT-BOX  device  can  be  updated  with  a  USB  cable  and 

using  a  Windows®  OS.  A  specific  third-party  software  is  required  to  perform  this 
operation, which can be download from the following link:  

 

http://www.st.com/web/en/catalog/tools/FM147/CL1794/SC961/SS1533/PF257916

 

 

After downloading the DfuSE software

, 

simply run the installer and follow the 

installation procedure. After installation, please prepare the CT-BOX for the firmware 
update following the described steps: 

 

•

 

Switch OFF the CT-BOX unit using the main switch present on the front panel 
of the device; 

•

 

Set  the  SWITCH  #1  on the  rear  panel  to  be  positioned  high,  as  illustrated  in 
Figure 13; 

 

Figure 13: 

SWITCH position for update firmware. 

 

•

 

Connect the CT-BOX to the computer using the USB cable; 

•

 

Switch ON the CT-BOX using the main switch, present on the front panel of 
the unit; 

•

 

The Windows® OS shall find and install the driver for the USB port; 

•

 

Launch the DfuSe Demonstration software; this should automatically find the 
DFU Device (i.e. the CT-BOX) connected to the USB port; 
 

 

Summary of Contents for CT-BOX

















Reviews:

No comments

Brands by name

Popular brands

Load more brands