BUSKRO BK730-2 User Manual Download

Page: 24 / 157

Chapter 2

BK730-2

Base

Page 2-10

Note that all input signals used in the unit are at a 12 VDC level (1kOhm pull-up to the

+12 VDC supply), looking for a dry contact (STOP and START

from

other machines),

while the unit provides dry contacts for those signals coming from other machines (STOP

and START

other machines). The only exception is the drive output to the heater

control which supplies a sw12 VDC and Ground to activate the relay in the Heater

Units.

Table 2-2

shows the options and explains the implications:

Table 2-2:

Base Control Board DIP Switch Settings

Configuration Explanation

S1-1 (CONV)

Enables or disables a STOP signal from the conveyor. If
no conveyor is used in the system, the switch should be set
to “disabled”.

S1-2 (UPSTR)

Enables or disables a STOP signal from an upstream
machine. If no upstream equipment is used in the system,
the switch should be set to “disabled”.

S1-3 (DNSTR)

Enables or disables a STOP signal from a downstream
machine. If no downstream equipment is used in the
system, the switch should be set to “disabled”.

S1-4 (JAM)

Enables or disables a STOP signal from the JAM sensor.
If no JAM sensor is used in the machine, the switch should
be set to “disabled”.

S1-5 (CONTR)

Enables or disables a STOP signal from the control
computer. If no computer is used with the machine, the
switch should be set to “disabled”.

Buskro Ltd.

BK730-2 Tabber

Summary of Contents for BK730-2






























































































































































Search results

Summary of Contents for BK730-2

Reviews:

Related manuals for BK730-2

Brands by name

Popular brands

BUSKRO BK730-2, User Manual

Search results

Summary of Contents for BK730-2

Reviews:

Related manuals for BK730-2

Brands by name

Popular brands