BUSCH MINK Instruction Manual Download Page 8 | Manualshive

Page: 8 / 36

background image

3 | Transport

8 | 36

Instruction Manual MINK MM 1104-1142 BV_EN_en

3

Transport

WARNING

Suspended load.
Risk of severe injury!

●

Do not walk, stand or work under suspended loads.

WARNING

Lifting the machine using the motor eye bolt.
Risk of severe injury!

●

Do not lift the machine using the eye bolt fitted to the motor. Only lift the machine as shown.

●

To find out the weight of the machine, refer to the chapter

Technical Data

29] or the name-

plate (NP).

●

Make sure that the eye bolt(s) (EB) is/are in faultless condition, fully screwed in and tightened by
hand.

●

Check the machine for transport damage.

If the machine is secured to a base plate:

●

Remove the machine from the base plate.

«
...
6
7
8
9
10
...
»

Summary of Contents for MINK





































Reviews:

No comments

Related manuals for MINK

Brand: Danfoss Pages: 8

Brand: Danner Pages: 2

Brand: Kärcher Pages: 8

nXDS10i nXDS15i

Brand: Edwards Pages: 58

BASIC VASF 2.120/1-0.AC115

Brand: Becker Pages: 6

Brand: Noritz Pages: 26

Brand: SAMES KREMLIN Pages: 51

SUNLINE 2000 B1CH180

Brand: York Pages: 20

Brand: Kayoba Pages: 16

Brand: Wayne Pages: 4

Brand: Altrad Pages: 30

Brand: Calorex Pages: 156

Brand: DAE Pumps Pages: 29

Brand: Zehnder Pumpen Pages: 34

Brand: hajdu Pages: 65

Brand: Waterous Pages: 7

Brand: BATHMATE Pages: 8

Brand: Genpar Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands