background image

Electrical Connection | 6

Instruction Manual MINK MM 1104-1142 BV_EN_en

15 | 36

Provide a lockable disconnect switch on the power line so that the machine is completely secured
during maintenance tasks.

Provide an overload protection according to EN 60204-1 for the motor.

Busch recommends installing a D-curve circuit breaker.

Connect the protective earth conductor.

Electrically connect the motor.

NOTICE

Incorrect connection.
Risk of damage to the motor!

The wiring diagrams given below are typical. Check the inside of the terminal box for motor con-
nection instructions/diagrams.

6.2

Wiring Diagram Three-Phase Motor

NOTICE

Incorrect direction of rotation.
Risk of damage to the machine!

Operation in the wrong direction of rotation can destroy the machine in a short time! Prior to
start-up, ensure that the machine is operated in the right direction.

Determine the intended direction of rotation with the arrow (stuck on or cast).

Jog the motor briefly.

If the rotation of the motor must be changed:

Switch any two of the motor phase wires.

Delta connection (low voltage):

Star connection (high voltage):

Double star connection, multi-voltage motor
with 9 pins (low voltage):

Star connection, multi-voltage motor with 9
pins (high voltage):

Summary of Contents for MINK





































Reviews: