background image

After Fitment:

After installing the tent it is a good idea to check for symmetry when lifting/lowering.

You can fine-tune how evenly the roof lifts/lowers by adjusting the turnbuckles. If you screw them in 

the roof will lift, if you screw them out the roof will lower – you have about 5cm to work with.

How to install a Solar Panel

PLEASE NOTE

 to be careful when drilling through to the inside of the tent as the drill bit might catch 

on the roof-lining and cause tears. Also ensure that the holes are properly sealed to insure that it is 

still dust/water tight.

How to add Solar Wiring afterwards

Add a Brad Harrison plug next to your current grey plug on the bottom frame. Add a Brad Harrison 

plug to the top frame. Connect the two with 6mm wiring that can go through the inside of your 

BunduTop – ensure the length is long enough. To eaten the appearance, you can run it through the 

canvas sleeve next to the arm that already contains wiring.

PLEASE NOTE

 that since the end of 2017 all tents are manufactured with solar wiring so the above 

will only be applicable as an upgrade to older tents.

How to add Fans and lights afterwards

You can order the 12v Fans or LED lights from the factory to install afterwards. The frames they 

come in have a clear aluminium area that gets fastened to the interior roof of the tent. Firstly decide 

on placement and with a blade remove the roof-lining – this insures that when you drill the holes to 

rivet/bolt the fan/light to the roof the drill bit does not catch on the material and cause tears.

Kindly use the wiring diagram as reference.

1.  Hold the bracket in position on the side of 

the tent where you will be entering your 

tent.

2.  Trace the outline.
3.  Mark where you want to place your 3 bolts 

and drill the holes.

4.  Hold the bracket in place again and mark 

the 3 holes you just drilled through the 

bracket onto the tent and drill them as well.

5.  Line up the holes on the bracket to the 

ones on the tent and bolt through both.

Remember to mount the ladder bracket:

After installing the tent mount the ladder bracket beneath the opening you will be using as the 

door. This way the ladder has a place to hook on to and will be less damaging than simply hooking 

the ladder onto the lip of the tent.

8

Summary of Contents for BunduTop















Reviews: