background image

The BunduTop standard size is 

2100 x 1350 x 300 mm when closed, 

and 2100 x 1350 x 1000 mm when open.

PLEASE NOTE 

you can order a custom sized 

BunduTop up to 1.6m wide and 3m long.

The tent weighs about 80 kgs.

The tent boasts entry from any side, giving you 360 access and view. Each window/door is

manufactured with the canvas on the outside and the mesh on the inside. This allows you to 

leave the windows open for ventilation, even in poor weather conditions

The BunduTop comes standard with an aluminium sliding ladder and 2 pockets inside to put 

keys, cellphones etc. and has a cigarette lighter plug and an LED light inside.

The roof of the BunduTop is a raw aluminium sheet to ensure maximum heat reflection and is 

the main reason you can sleep comfortably cool inside, even in direct sunlight.

The roof weighs 20 kgs and can carry additional weight of 25 kgs, if evenly spread.

You are welcome to install a solar panel on top. We now include solar wiring and it simplifies the 

installation of a solar panel by allowing the wiring to go unseen through the tent.

The 2000lbs winch motor lifts and lowers the tent with the use of 3mm Dyneema rope on a 

pulley system.

The foam backed roof-lining absorbs moisture and condensation, but if you are going to

extremely cold areas we do recommend putting a carpet under the mattress as insulation, as 

very cold temperatures creates additional condensation.

The frame built into the bottom of the tent provides additional strength and makes it versatile to 

mount. It can be bolted directly to your load bars or roof rack.

The mattress inside is 2000 x 1250 x 100 mm and is made from a high density foam. A double 

bed fitted sheet fits it just fine. This leaves enough space inside the tent so that you can leave 

your bedding inside.

Kindly arrange your bedding so that it can’t hook into the rope system inside; flattened bedding 

won’t interfere.

Please ensure you leave some windows open or close only the mosquito net so that trapped air 

can escape. Trapped air will push out the canvas sides and cause it to not fold in properly when 

lowering the tent.

When entering or exiting the tent, ensure that the zips are completely zipped down as the zips/

mosquito net isn’t designed to carry weight. 

The tent has been tested extensively in various locations and weather types. In the USA it has 

proven to withstand 50 mph winds and has also performed well in snow.

The

BunduTop

DO NOT OPEN THE TENT WHILE THE LATCHES ARE 

STILL CLOSED AS THIS WILL DAMAGE THE TENT.

Summary of Contents for BunduTop















Reviews: