Bull DPX/20 Installing And Maintaining Download Page 31 | Manualshive

Page: 31 / 69

background image

3–7

Chapter 3. Installing multiple storage systems on a SCSI bus

2. If the server has a

9-pin

male

connector for the RS-232 port, attach the adapter

cable’s 9-pin connector into the server’s RS-232 connector.

Attaching an adapter cable

Server’s RS-232

connector

3. Attach the male end of the asynchronous (console) cable to either the server’s

RS-232 connector or the 25-pin connector on the adapter cable.

4. Attach the other end of the asynchronous cable to the SP’s

CONSOLE

connector.

Attaching a cable to the SP’s console connector

SP

Flat blade

screwdriver

«
...
29
30
31
32
33
...
»

Summary of Contents for DPX/20






































































Reviews:

No comments

Related manuals for DPX/20

Brand: Panasonic Pages: 16

Brand: Panasonic Pages: 12

BLPA100KTA - HD-PLC ETHERNET ADAPT.2PK

Brand: Panasonic Pages: 2

Brand: AGFEO Pages: 12

Brand: Xantech Pages: 2

Brand: AzureWave Pages: 31

Brand: Dynex Pages: 24

BasicXL BXL-NBT-AC01

Brand: nedis Pages: 16

Brand: nedis Pages: 30

Brand: nedis Pages: 2

Brand: Eskridge Pages: 4

Brand: Siemens Pages: 4

Brand: Siemens Pages: 2

Brand: Siemens Pages: 8

Brand: Siemens Pages: 10

Brand: Siemens Pages: 42

Brand: Kramer Pages: 18

Brand: Black Box Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands