Bull DPX/20 Installing And Maintaining Download Page 59

Page: 59 / 69

B-1

Appendix B. Spare parts for DAS 150

Spare parts for DAS 150

This appendix lists the available spare parts for the DAS 150 storage system.

Bull Part Number

Description

DGC005–042215

Fan module

DGC005–042077

Power supply

DGC005–041958

Storage Processor

DGC005–043225

Storage Processor with write cache

DGC116–007158

Kit PCMCIA board

DGC005–042318

2 GB Disk module (5400 rpm)

DGC005–042214

DAS 150 Chassis with fan and power supply

DGC002–046314

Disk module filler panel

DGC005–032921

Female/female gender changer for asynchronous cable

DGC005–036787

9/25 Asynchronous adapter cable

DGC005–033788

6 m Asynchronous cable

DGC118–021822

6 m Wide SCSI cable (MCA adapter to DAS)

DGC005–041275

6 m Wide SCSI cable (PCI adapter to DAS)

DGC005–040004

6 m Wide SCSI cable (DAS to DAS)

DGC111–003454

Wide SCSI bus differential terminator

DGC109–000719

110/120 V Power cord STD US

DGC109–000810

110/120 V Power cord SWISS

DGC109–000811

220 V Power cord ITALY

DGC109–000812

220/240 V Power cord EUROPE

DGC109–000813

210 V Power cord UK

DGC109–000815

240 V Power cord DENMARK

End of Appendix

Summary of Contents for DPX/20






































































Search results

Summary of Contents for DPX/20

Reviews:

Related manuals for DPX/20

Brands by name

Popular brands

Bull DPX/20, Installing And Maintaining

Search results

Summary of Contents for DPX/20

Reviews:

Related manuals for DPX/20

Brands by name

Popular brands