Buffalo Tech WPL-05G300 Series User Manual Download Page 17

Page: 17 / 140

Room 2

Room 3

AirStation

AirStation
(Extender kit)

PLC button

WPL-05G300 Series User Manual

Chapter 2 Installation

Hold down the PLC button of the AirStation installed in
step 2 until the power LED starts blinking green (about
2 seconds).

Within 2 minutes, hold down the
PLC button of the AirStation that
was installed in step 1 until the
power LED starts blinking green
(about 2 seconds).

Check that the PLC LED changes to steady green after about 1 minutes.

Note:

If the PLC LED does not turn steady green after about one minute, perform the setup procedure again
from the beginning.

Check that the LEDs appear as shown below.

Power

Green LED on

PLC

Off

Wireless

Green LED on or blinking

Router

Off

For LED locations, refer to chapter 1.

Summary of Contents for WPL-05G300 Series













































































































































Search results

Summary of Contents for WPL-05G300 Series

Reviews:

Related manuals for WPL-05G300 Series

Brands by name

Popular brands

Buffalo Tech WPL-05G300 Series, User Manual

Search results

Summary of Contents for WPL-05G300 Series

Reviews:

Related manuals for WPL-05G300 Series

Brands by name

Popular brands