background image

22

Table 4 – Dry Coil Air Delivery CFM* -- Horizontal and Downflow Discharge -- Unit 607----A24--60

Unit

Motor Speed

Wire Color

External Static Pressure (in W.C)

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

607----A24

Low

Blue

cfm

754

650

536

429

---

---

---

---

---

Med-Low

Pink

cfm

851

777

675

591

475

---

---

---

---

Medium

1

Red

cfm

941

851

774

684

576

479

---

---

---

Med-High

Orange

cfm

1009

917

840

759

667

577

447

---

---

High

Black

cfm

1241

1167

1111

1036

969

881

818

731

640

607----A30

Low

Blue

cfm

741

638

547

415

---

---

---

---

---

Med-Low

Pink

cfm

973

887

823

733

665

538

451

---

---

Medium

Red

cfm

1088

1023

954

881

800

723

658

563

461

Med-High

1

Orange

cfm

1140

1064

996

915

840

758

687

564

480

High

Black

cfm

1202

1140

1082

1015

961

881

810

732

631

607----A36

Low

Blue

cfm

1176

1121

1079

1019

974

920

877

826

754

Med-Low

Pink

cfm

1295

1234

1182

1126

1075

1016

955

898

857

Medium

1

Red

cfm

1345

1282

1235

1194

1140

1095

1027

974

921

Med-High

Orange

cfm

1505

1452

1413

1358

1323

1282

1234

1169

1130

High

Black

cfm

1705

1643

1607

1568

1518

1483

1448

1404

1360

607----A42

Low

Blue

cfm

1295

1234

1182

1126

1075

1016

955

898

857

Med-Low

Pink

cfm

1345

1282

1235

1194

1140

1095

1027

974

921

Medium

Red

cfm

1505

1452

1413

1358

1323

1282

1234

1169

1130

Med-High

1

Orange

cfm

1545

1492

1449

1411

1362

1313

1278

1231

1188

High

Black

cfm

1705

1643

1607

1568

1518

1483

1448

1404

1360

607----A48

Low

Blue

cfm

1430

1374

1327

1267

1223

1176

1127

1061

1016

Med-Low

Pink

cfm

1445

1389

1341

1281

1236

1189

1139

1072

1027

Medium

1

Red

cfm

1678

1635

1602

1558

1513

1474

1438

1404

1349

Med-High

Orange

cfm

2131

2088

2065

2013

1982

1941

1888

1860

1785

High

Black

cfm

2461

2409

2339

2286

2192

2140

2062

1968

1874

607----A60

Low

Blue

cfm

1445

1389

1341

1281

1236

1189

1139

1072

1027

Med-Low

Pink

cfm

1678

1635

1602

1558

1513

1474

1438

1404

1349

Medium

1

Red

cfm

1962

1915

1880

1843

1794

1753

1711

1675

1628

Med-High

Orange

cfm

2131

2088

2065

2013

1982

1941

1888

1860

1785

High

Black

cfm

2461

2409

2339

2286

2192

2140

2062

1968

1874

* Air delivery values are without air filter and are for dry coil (See 607--- ---A Wet Coil Pressure Drop Table).

1

Factory---shipped cooling/heat pump heating speed

NOTE

: Deduct field---supplied air filter pressure drop and wet coil pressure drop to obtain external static pressure available for ducting.

Shaded areas indicate speed/static combinations that are not permitted for dehumidification speed.

Table 5 – 607----A Wet Coil Pressure Drop (in. W.C.)

UNIT SIZE

STANDARD CFM (S.C.F.M)

500

600

700

800

900

1000

1100

1200

1300

1400

1500

1600

1700

1800

1900

2000

24

0.06

0.07

0.08

0.09

0.1

30

0.12

0.15

0.19

0.23

0.27

36

0.07

0.11

0.18

0.26

0.35

42

0.04

0.07

0.10

0.15

0.21

48

0.11

0.14

0.17

0.22

0.28

60

0.10

0.17

0.23

0.31

0.36

Table 6 – Wet Coil Air Delivery (CFM) - Downflow -- High Speed with 1--in. (25 mm) Filter and Economizer

UNIT SIZE

EXTERNAL STATIC PRESSURE (in. W.C.)

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1.0

36, 42

1612

1569

1527

1481

1451

1393

1351

1317

1278

1242

48

2298

2239

2180

2110

2044

1951

1862

1777

1697

1591

60

2298

2239

2180

2110

2044

1951

1862

1777

1697

1591

Table 7 – Filter Pressure Drop Table (in. W.C.)

FILTER SIZE

in. (mm)

CFM

500

600

700

800

900

1000

1100

1200

1300

1400

1500

1600

1700

1800

1900

2000

2100

2200

2300

20X20X1

(508X508X25)

0.05

0.07

0.08

0.1

0.12

0.13

0.14

0.15

20X24X1

(508X610x25)

.09

.10

.11

.13

.14

.15

.16

24X30X1

(610X762x25)

0.04

0.05

0.06

0.07

0.07

0.08

0.09

0.10

24X36X1

(610X914X25)

0.06

0.07

0.07

0.08

0.09

0.09

0.10

0.11

0.12

0.13

0.14

0.14

Table 8 – Electric Heat Pressure Drop Table (in. W.C.)

Small Cabinet: 24--36 CFM

STATIC

CFM

500

600

700

800

900

1000

1100

1200

1300

1400

1500

1600

5kw

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.00

0.02

0.04

0.06

0.07

7.5 kw

0.00

0.00

0.00

0.00

0.00

0.00

0.02

0.03

0.05

0.07

0.08

0.09

10 kw

0.00

0.00

0.00

0.00

0.00

0.02

0.04

0.06

0.07

0.09

0.10

0.11

15 kw

0.00

0.00

0.00

0.02

0.04

0.06

0.08

0.10

0.12

0.14

0.16

0.18

20 kw

0.00

0.00

0.02

0.04

0.06

0.08

0.09

0.11

0.13

0.15

0.17

0.19

Electric Heat Pressure Drop Table (in. W.C.)

Large Cabinet 42--60 CFM

STATIC

CFM

1100

1200

1300

1400

1500

1600

1700

1800

1900

2000

2100

2200

2300

2400

2500

5kw

0.00

0.00

0.00

0.01

0.02

0.03

0.04

0.05

0.06

0.07

0.08

0.09

0.10

0.11

0.12

7.5 kw

0.00

0.00

0.01

0.02

0.03

0.04

0.05

0.06

0.07

0.08

0.09

0.10

0.11

0.12

0.13

10 kw

0.00

0.00

0.01

0.02

0.03

0.04

0.05

0.06

0.07

0.08

0.09

0.10

0.11

0.12

0.13

15 kw

0.00

0.02

0.03

0.04

0.05

0.06

0.07

0.08

0.09

0.10

0.11

0.12

0.13

0.14

0.15

20 kw

0.02

0.03

0.04

0.05

0.06

0.07

0.08

0.09

0.10

0.11

0.12

0.13

0.14

0.15

0.16

607C

--

--

A

Summary of Contents for PREFERRED 607C--A Series



















































Reviews: