background image

Great Bay Community College 

    Document 

Number: 

1.16.1 

320 

Corporate 

Drive 

      Revision 

Number: 

Portsmouth, 

NH 

03801      Effective 

Date: 

20May09 

 

 

 

 

 

 

        Page 16 of 20                                 

Title: New Brunswick BioFlo 3000 Bioreactor SOP

 

 

 

 

Figure 1:  BioFlo 3000 Vessel and Cabinet 

 

1.

 

Heat Exchanger Base 

2.

 

Jacket Water Line Adaptors 

3.

 

Heat Exchanger Connectors  

4.

 

Bottom Steel Ring 

5.

 

Glass Vessel 

6.

 

Condenser Water Lines 

7.

 

Top Steel Ring 

8.

 

Agitator Shaft 

9.

 

Agitator Cover 

10.

 

Condenser Top Outlet 

11.

 

Electrical Outlet 

12.

 

Sparger Gas Port 

13.

 

Agitator Motor Stand 

14.

 

Cabinet 
 

15.

 

Probe Stand 

16.

 

Controller Display 

17.

 

pH Probe Shorting Cap 

18.

 

Controller Keypad 

19.

 

pH Probe 

20.

 

DO Probe 

21.

 

Feed Pump 

22.

 

pH Probe Protective Cap 

23.

 

Feed Bottle Assembly 

24.

 

Agitator Motor 

25.

 

Platform 

26.

 

Silicone Tubing 

27.

 

Air Filter 

28.

 

PharMed Tubing 

29.

 

Plastic Plug 

 

26

Summary of Contents for BIOFLO 3000





















Reviews: