manualshive.com logo in svg

Bruker minispec mq20, User Manual, Page: 65 / 86

Share
Download
Bruker minispec mq20 User Manual Download Page 65

minispec.exe Software for Diagnostic and Service Purposes

E1400912_1_001

65

8.3.6.4

The Repetitive Measurement Settings Command

Repetitive  measurements  require  several  control  parameters.  When  this  command  is
selected, a table appears where the following parameters can be specified: the waiting time
in  seconds  before  a  repetitive  minispec  measurement  begins,  the  delay  between  two
successive repetitions, and the maximum number of repetitive measurements.

8.3.7

The View Menu

Each user can configure the screen for the special requirements of a measurement. With the
help  of  the  pull-down  menu 

View

  one  can  adjust  the  arrangement  of  the  different  windows,

the display of toolbars, the font size for the result output and much more. The list of available
commands depends on the active window and the active application:

Figure 8.12: The View Pull-Down Menu

The View Default and the Toolbars Commands

The  minispec  software  shows  four  tool  bars:  the  Standard  Tool  Bar,  the  Result  Bar,  the
Measurement  Tool  Bar  and  the  Info  Tool  Bar  (see  the  figure  above).  When  the  minispec
software is configured as the Relaxation Time or NMR Analyzer type, all toolbars are docking
toolbars. This means that the toolbars can be moved to any location on the entire screen by
pressing  and  holding  the  left  mouse  key.  The  location  can  be  outside  of  the  minispec
software main window, within the main window docked (e.g. on the left, right, top or bottom),
or switched off entirely. To switch toolbars on and off, mark/unmark the corresponding toolbar
in the minispec application menu 

View

.

To get an impression of the toolbars and to restore the default screen select 

View Default

.

Shortcut Keys: ALT+V

The Info Views Command

This command is subdivided into four parts:

1.

minispec Settings:

 If you choose this item you will get a table of all minispec application

relevant instrument settings and parameters. 
Shortcut: Info Toolbar:

The function is disabled (grayed) if no minispec is connected.

2.

minispec System Status:

 The user can get a real-time indication of the status of the

minispec instrument, particularly:

– Magnet Unit temperature and status.

– Sample orifice status (sample inserted or not).

– Sample insertion detection (grayed if sample detection is set OFF.

Summary of Contents for minispec mq20























































































Reviews:

No comments